I hadn't seen this in all my searches over the last couple of days. Then just a few moments ago I found an official site. I searched hi and lo for some images on the internet and found a site with a lot of them including T63 but couldn't get it to work. The model is based on the Boyue T63 and the T62D image didn't work. After having got it stuck in recovery mode I had tried downloading and installing different images for the T62+. Many thanks to all the posters on this thread. ☺įinally managed to get tmy Inkbook Obsidian back up and running again.
![inkbook model t62 inkbook model t62](https://live.staticflickr.com/65535/50330697541_fcc9b9d775_k.jpg)
#Inkbook model t62 android
For sure a good learning experience on android though. I'm doing all this as an experiment as I want to run an app when I fly my paraglider. I sent a mail to,Artatech asking what the key sequence is to hard reset the device as I am sure there must be a way for the typical end user., I am also trying using adb with the shell reboot wipe data command but the shell is not available in recovery mode. Only problem is that I cannot get the menu to appear in recovery mode.,I have tried all key combinations using power and the two page buttons. So now i'm trying to do a factory reset hoping the original firmware will be on the recovery partition.
#Inkbook model t62 update
I loaded the August '15 update and that fully loaded but at reboot it got stuck in a boot loop. No,OTG though so I thought I'd try an earlier update and see if that fully installed.
![inkbook model t62 inkbook model t62](http://imagizer.imageshack.us/v2/xq90/905/0Pl5wo.jpg)
I did a reboot and it loaded with the new boyue UI. The february '16 update started to load but partly failed and ended up at recovery screen. I got a little impatient and went ahead and tried the update before backing up. Host diagnostic app also reported not working., I haven't tried powered yet as Andy got his card reader working without that. I firmly recommend reading all of this thread otherwise the chance to brick your device is higher than the chance of success. Ro.=dalvik.vm.dexopt-flags=m=yĭalvik.vm.stack-trace-file=/data/anr/traces.txtįor this, you should read more about it. Ro.config.notification_sound=pixiedust.ogg
![inkbook model t62 inkbook model t62](https://cdn.shopify.com/s/files/1/1356/4477/products/3_0f746881-1eac-4890-8613-0ccb9d35efd2_2048x2048.jpg)
#rild.libpath=/system/lib/libreference-ril.so Ro.scription=rk30sdk-eng 4.2.2 JDQ39 48 test-keys # ro.build.product is obsolete use ro.vice Here is the build.prop file for reference if it helps. On the inkbook obsidian I don't believe I have a refresh button so not sure what that may be on this device.Īny help appreciated. Secondly, to update the device, do you believe it is possible to just use the update.zip file for the T62D firmware from feb 2016 that andyisb used above to get his usb keyboard via power otg working? I read in this thread there is a sequence to use to get the update to apply, namely hold power and refresh buttons, then after 5s let go of the power button. if someone could tell me the adb commands to do that or an alternative method I'd be much obliged. It seems the Inkbook Obsidian is some form of T63 (see build.prop file below for details) and that the T63 is really a T62+ platform and that the T62D firmware could work on it and therefore get hopefully OTG working.īefore I do any firmware update I'd like to be able to save the current build on the device. I have rooted the inkbook with kingroot and I have ADB enabled and working with the device. I have read all of this thread with great interest.
#Inkbook model t62 windows
I should say I'm a newbie with Android devices but have a lot of experience with windows devices. It seems the Boyue T62+ is capable of doing that and I saw andyinsb got that working. I think it should be capable of doing that based on the information I have read on the web and in this thread about it being the same as a Boyue T62+.
![inkbook model t62 inkbook model t62](https://arcanesceneryandmodels.co.uk/wp-content/uploads/imported/Tamiya-T62A-RUSSIAN-ARMY-TANK-135-Scale-Kit-108-400662507494-800x532.jpg)
I have an Inkbook obsidian that I'd like to get OTG enabled on.